ORDRSP Purchase order response
TBG1 Supply Chain
A message from the seller to the buyer, responding to a purchase order message or a purchase order change request message.
Header
- 00010Message headerMandatoryMax 1
A service segment starting and uniquely identifying a message. The message type code for the Purchase order response message is ORDRSP. Note: Purchase order response messages conforming to this document must contain the following data in segment UNH, composite S009: Data element 0065 ORDRSP 0052 D 0054 18A 0051 UN
1. Data element S009/0057 is retained for upward compatibility. The use ofS016 and/or S017 is encouraged in preference.2. The combination of the values carried in data elements 0062 and S009 shallbe used to identify uniquely the message within its group (if used) or ifnot used, within its interchange, for the purpose of acknowledgement. - 00020Beginning of messageMandatoryMax 1
A segment by which the sender must uniquely identify the order response by means of its number and when necessary its function. - If the MESSAGE FUNCTION CODE is a "12", "27" or "29" indicating that the total message was not processed, rejected or accepted. No segments, other than mandatory segments, need be used in the message Header, Detail or Summary sections. However for positive reporting purposes all the segments of the ORDERS or ORDCHG message, being responded to, may be used in ORDRSP. - If the MESSAGE FUNCTION CODE is a "28" indicating an accepted ORDERS or ORDCHG message with amended heading information or "34" indicating amendment in the message, then all segments in the heading section must be used from the ORDRES or ORDCHG message being responded to. This includes both amended and non amended segments. If the ORDERS message was "NOT PROCESSED"; use of MESSAGE FUNCTION CODE "12" indicates acknowledgement that the transmitted message has been received and understood by the seller, but remains to be processed within his application system. If the Order or Order Change message was "NOT ACCEPTED"; use of MESSAGE FUNCTION CODE "27" indicates that the seller declines to supply the goods or declines to accept the changes requested in a Purchase Order Change Request. If the ORDER or ORDER CHANGE message was "ACCEPTED, WITH AMENDMENT IN HEADING SECTION"; use of MESSAGE FUNCTION CODE "28" indicates that the seller accepts to supply the goods or services requested in the Purchase Order (or a Purchase Order Change Request), but requires one or more changes to the terms set out in the referenced message Heading Section. The complete Heading Section data is transmitted to replace all data previously sent. The Detail Section is considered as acknowledged without change. If the ORDER or ORDER CHANGE message was "ACCEPTED, WITHOUT AMENDMENT"; use of MESSAGE FUNCTION CODE "29" indicates that the seller according to the terms set out in the Purchase Order or a Purchase Order Change Request accepts to supply the goods or services requested or where appropriate accepts the cancellation. If the ORDER or ORDER CHANGE message was "ACCEPTED, WITH AMENDMENT IN DETAIL SECTION"; use of MESSAGE FUNCTION CODE "30" indicates that the seller accepts to supply the goods or services requested in the Purchase Order (or a Purchase Order Change Request), but requires changes in one or more line items (as indicated in the LIN segments). The Heading Section is considered as acknowledged without change If the ORDER or ORDER CHANGE message was "ACCEPTED WITH AMENDMENT"; use of MESSAGE FUNCTION CODE "34" indicates that the seller accepts to supply the goods or services requested in the Purchase Order and Purchase Order Change Request, but requires changes in the Heading as well as Detail Section.
- 00030Date/time/periodMandatoryMax 35
A segment specifying general dates and, when relevant, times related to the whole message. The segment must be specified at least once to identify the order response date. Examples of the use of this DTM segment are: Lead times that apply to the whole of the Order response and, if no schedule is to be specified, the delivery date. The Date/time/period segment within other Segment groups should be used whenever the date/time/period needs to be logically related to another specified data item. e.g. Payment due date is specified within the PYT Segment group.
- 00040Payment instructionsConditionalMax 1
A segment requesting or confirming conditions of payment, guarantee and method of payment for the whole order response An example of the use of this segment is to specify that a documentary credit will be used.
- 00050Additional informationConditionalMax 5
A segment indicating special conditions related to the total order response owing to origin, customs preference, or other commercial factors.
- 00060Item descriptionConditionalMax 999
A segment providing a description common to all line items of the order response.
- 00070Free textConditionalMax 99
A segment with free text information, in coded or clear form, used when additional information is needed but cannot be accommodated within other segments. In computer to computer exchanges such text will normally require the receiver to process this segment manually.
- 00080Related identification numbersConditionalMax 10
A segment providing related identification numbers common to all line items.
- Segment group 1Repeat 9999
- 00100ReferenceMandatoryMax 1
A segment identifying the reference by its number and where appropriate a line number within a document.
- 00110Date/time/periodConditionalMax 5
A segment specifying the date/time related to the reference.
- 00100ReferenceMandatoryMax 1
- Segment group 2Repeat 1
- 00130Adjustment detailsMandatoryMax 1
A segment giving adjustment details.
- 00140Free textConditionalMax 5
A segment giving additional information on the adjustment.
- 00130Adjustment detailsMandatoryMax 1
- Segment group 3Repeat 99
- 00160Name and addressMandatoryMax 1
A segment identifying names and addresses of the parties, in coded or clear form, and their functions relevant to the order response. Identification of the seller and buyer parties is mandatory for the order response message. It is recommended that where possible only the coded form of the party ID should be specified. e.g. The Buyer and Seller are known to each other, thus only the coded ID is required, but the Consignee or Delivery address may vary and would have to be clearly specified, preferably in structured format.
- 00170Place/location identificationConditionalMax 25
A segment giving more specific location information of the party specified in the NAD segment e.g. internal site/building number.
- 00180Financial institution informationConditionalMax 5
A segment identifying the financial institution (e.g. bank) and relevant account numbers for the seller, buyer and where necessary other parties. e.g. the buyer may provide a choice of financial institutions for direct debit purposes.
- Segment group 4Repeat 99
- 00200ReferenceMandatoryMax 1
A segment identifying the reference by its number and where appropriate a line number within a document.
- 00210Date/time/periodConditionalMax 5
A segment specifying the date and/or time related to the reference.
- 00200ReferenceMandatoryMax 1
- Segment group 5Repeat 5
- 00230Document/message detailsMandatoryMax 1
A segment identifying and providing information relating to the documents required by the party specified by the NAD segment. For example, the party may require a Certificate of Analysis.
- 00240Date/time/periodConditionalMax 5
A segment specifying the date and/or time of the document.
- 00230Document/message detailsMandatoryMax 1
- Segment group 6Repeat 5
- 00260Contact informationMandatoryMax 1
A segment to identify a person or department, and their function, to whom communications should be directed.
- 00270Communication contactConditionalMax 5
A segment to identify a communications type and number for the contact specified in the CTA segment.
- 00260Contact informationMandatoryMax 1
- 00160Name and addressMandatoryMax 1
- Segment group 7Repeat 5
- 00290Duty/tax/fee detailsMandatoryMax 1
A segment specifying a tax type, category and rate, or exemption, relating to the whole order response. e.g. Value Added Tax at the standard rate is applicable for all items.
- 00300Monetary amountConditionalMax 1
A segment specifying the amount for the identified tax/fee.
- 00310Place/location identificationConditionalMax 5
A segment indicating the location to which the tax or exemption specified in the tax segment applies, e.g. city or state or country.
- 00290Duty/tax/fee detailsMandatoryMax 1
- Segment group 8Repeat 5
- 00330CurrenciesMandatoryMax 1
A segment identifying the currencies in the order response, e.g. the order currency. A rate of exchange may be given to convert a reference currency into a target currency.
- 00340Percentage detailsConditionalMax 5
A segment specifying the fluctuation beyond those limits will allow one or either party to re-negotiate prices.
- 00350Date/time/periodConditionalMax 5
A segment specifying the date/time/period related to the rate of exchange.
- 00330CurrenciesMandatoryMax 1
- Segment group 9Repeat 10
- 00370Payment termsMandatoryMax 1
A segment identifying the payment terms and date/time basis.
- 00380Date/time/periodConditionalMax 5
A segment giving the specific date/time/period, if needed, of any payments, discounts, instalments etc.
- 00390Percentage detailsConditionalMax 1
A segment specifying the discount, interest, penalty as well as instalment percentage.
- 00400Monetary amountConditionalMax 1
A segment specifying amounts related to payment discounts, penalties or instalments.
- 00370Payment termsMandatoryMax 1
- Segment group 10Repeat 10
- 00420Transport informationMandatoryMax 1
A segment specifying the mode, means and identification of the transport for the goods. If required, the carrier's address should be indicated within the NAD Segment group.
040 D5(040,030) If first, then all - Segment group 11Repeat 10
- 00440Place/location identificationMandatoryMax 1
A segment identifying locations relevant to the transport specified in the TDT segment. e.g. place of departure or border crossing point.
- 00450Date/time/periodConditionalMax 5
A segment identifying the date/time details of departure and/or arrival of the transported goods for the specified location.
- 00440Place/location identificationMandatoryMax 1
- 00420Transport informationMandatoryMax 1
- Segment group 12Repeat 5
- 00470Terms of delivery or transportMandatoryMax 1
A segment identifying the delivery terms to be used. e.g. UN INCOTERMS code could be used to specify the delivery terms.
- 00480Place/location identificationConditionalMax 2
A segment identifying locations relevant to the delivery terms specified in the TOD segment.
- 00470Terms of delivery or transportMandatoryMax 1
- Segment group 13Repeat 99
- 00500PackageMandatoryMax 1
A segment specifying the number and type of packages for the whole order response, e.g. number and type of pallets.
- 00510MeasurementsConditionalMax 5
A segment specifying physical measurements of packages described in the PAC segment. e.g. package length, weight.
- Segment group 14Repeat 99
- 00530Package identificationMandatoryMax 1
A segment specifying markings and labels used on individual physical units (packages) described in the PAC segment.
- 00540ReferenceConditionalMax 1
A segment identifying the master label number.
- 00550Date/time/periodConditionalMax 5
A segment specifying the dates relevant to the package markings.
- 00560Goods identity numberConditionalMax 99
A segment identifying the number or ranges of numbers for use with the package markings.
- 00530Package identificationMandatoryMax 1
- 00500PackageMandatoryMax 1
- Segment group 15Repeat 10
- 00580Equipment detailsMandatoryMax 1
A segment to define information regarding equipment to be used in conjunction with the whole order, and if required, to indicate responsibility for supply of the equipment.
- 00590Handling instructionsConditionalMax 5
A segment providing information on required handling of materials and additionally, if required, identifying hazardous materials.
- 00600MeasurementsConditionalMax 5
A segment providing measurement information for the equipment.
- 00610Free textConditionalMax 5
A segment with free text information, in coded or clear form, used when additional information is needed but cannot be accommodated within other segments. In computer to computer exchanges such text will normally require the receiver to process this segment manually.
- 00580Equipment detailsMandatoryMax 1
- Segment group 16Repeat 10
- 00630Scheduling conditionsMandatoryMax 1
A segment specifying the type and status of the schedule being given, and optionally defining a pattern to be established, e.g. firm or proposed delivery schedule for a weekly pattern.
- 00640Free textConditionalMax 5
A segment with free text information, in coded or clear form, to give further clarification to scheduling instructions. In computer to computer exchanges such text will normally require the receiver to process this segment manually.
- 00650ReferenceConditionalMax 5
A segment for specifying the reference for schedule.
- Segment group 17Repeat 10
- 00670QuantityMandatoryMax 1
A segment to specify pertinent quantities relating to the schedule and pattern established in the SCC segment, e.g. delivery quantity.
- 00680Date/time/periodConditionalMax 5
A segment indicating the date/time details relating to the quantity and schedule used to indicate date/time ranges, e.g. start and end dates for a delivery pattern, or delivery window.
- 00670QuantityMandatoryMax 1
- 00630Scheduling conditionsMandatoryMax 1
- Segment group 18Repeat 25
- 00700Additional price informationMandatoryMax 1
A segment to identify additional pricing information such as a price multiplier, the class or type of trade and additionally identifying the reason for any changes.
- 00710Date/time/periodConditionalMax 5
A segment to identify the date/time/period information related to the price change. e.g. period of validity.
- 00720Range detailsConditionalMax 1
A segment to identify the quantity or amount ranges to which the additional price information applies.
- 00700Additional price informationMandatoryMax 1
- Segment group 19Repeat 99
- 00740Allowance or chargeMandatoryMax 1
A segment identifying the charge or allowance and, where necessary its calculation sequence.
- 00750Additional informationConditionalMax 5
A segment indicating that the allowance or charge specified is subject to special conditions owing to origin, customs preference or commercial factors.
- 00760Date/time/periodConditionalMax 5
A segment to identify the date/time/period information related to the allowance or charge, e.g. period of validity.
- Segment group 20Repeat 1
- 00780QuantityMandatoryMax 1
A segment identifying the type of quantity and the quantity related to the allowance or charge.
- 00790Range detailsConditionalMax 1
A segment specifying, if required, the range to which the allowance or charge applies.
- 00780QuantityMandatoryMax 1
- Segment group 21Repeat 1
- 00810Percentage detailsMandatoryMax 1
A segment identifying the percentage and the percentage basis for the calculation of the allowance or charge.
- 00820Range detailsConditionalMax 1
A segment specifying, if required, a range for the application of the percentage.
- 00810Percentage detailsMandatoryMax 1
- Segment group 22Repeat 2
- 00840Monetary amountMandatoryMax 1
A segment identifying monetary amounts for the allowance or charge.
- 00850Range detailsConditionalMax 1
A segment specifying, if required, a range for the application of the allowance/charge amount.
- 00840Monetary amountMandatoryMax 1
- Segment group 23Repeat 1
- 00870Rate detailsMandatoryMax 1
A segment specifying the rate per unit and the basis for calculation.
- 00880Range detailsConditionalMax 1
A segment specifying, if required, the range for the application of the allowance/charge rate.
- 00870Rate detailsMandatoryMax 1
- Segment group 24Repeat 5
- 00900Duty/tax/fee detailsMandatoryMax 1
A segment specifying the tax type, category and rate, or exemption, related to the allowance or charge.
- 00910Monetary amountConditionalMax 1
A segment specifying the tax amount for the allowance or charge.
- 00900Duty/tax/fee detailsMandatoryMax 1
- 00740Allowance or chargeMandatoryMax 1
- Segment group 25Repeat 999
- 00930Requirements and conditionsMandatoryMax 1
A segment to enable industry or national requirements to be specified.
- 00940ReferenceConditionalMax 5
A segment identifying the referenced document by its number and, where appropriate, a line number.
- 00950Date/time/periodConditionalMax 5
A segment indicating the date/time details relating to the references.
- 00960Free textConditionalMax 99999
A segment with free text information, in coded or clear form, used when additional information is needed but cannot be accommodated within other segments. In computer to computer exchanges such text will normally require the receiver to process this segment manually.
- 00930Requirements and conditionsMandatoryMax 1
- Segment group 26Repeat 99
- 00980External file link identificationMandatoryMax 1
This segment will identify the external files by indicating the file name, file number and its sequence number in an exchange.
- 00990Computer environment detailsConditionalMax 99
To give precise definitions of all necessary elements belonging to the configuration of a computer system, e.g. hardware, firmware, operating system, communication and application software.
- 01000Communication contactConditionalMax 9
To identify a communication number of a department or a person to whom communication should be directed.
- 01010ReferenceConditionalMax 9
A segment giving reference related to the file identified by a previous external file link identification segment.
- 01020Date/time/periodConditionalMax 9
This segment will convey the date/time details of the external file.
- 01030QuantityConditionalMax 9
The size/volume of the external file identified in the previous external file link identification segment. external file.
- 00980External file link identificationMandatoryMax 1
Detail
- Segment group 27Repeat 200000
- 01050Line itemMandatoryMax 1
A segment identifying the line item by the line number and configuration level, and additionally, identifying the product or service ordered. Other product identification numbers, e.g. Buyer product number, etc., can be specified within the following PIA segment. The following Semantic Note concern the use of D/E 1229 Action Request Code for segment group 26. If the MESSAGE FUNCTION CODE is "30" indicating that there is amended detail data or "34" indicating amendments in the message, only the "amended" or "referenced" LIN segments, and all their subordinate segments, need to be included in the detail section. If the MESSAGE FUNCTION CODE is other than "30" or "34" there are no amendments to the detail section and the entire section is not required in the message. However for positive acknowledgement purposes, users may wish to resend the entire detail section of the ORDERS or ORDCHG message. The value of the ACTION REQUEST CODE in the included LIN segment will indicate the extent of amendment or reference use. If the line item has not yet been processed and is not being formally acknowledged an ACTION REQUEST CODE "4" indicates "NO ACTION". If the seller accepts to supply the line item an ACTION REQUEST CODE (D/E 1229) "5" indicates "ACCEPTED WITHOUT AMENDMENT". If the seller accepts to supply the line item, but requires one or more amendments to the terms set out in the referenced message, as indicated by the data following the LIN segment. An ACTION REQUEST CODE "6" indicates "ACCEPTED WITH AMENDMENT". If the seller declines to supply the line items in a Purchase Order, or in a Purchase Order Change Request an ACTION REQUEST CODE "7" indicates "NOT ACCEPTED". If the seller indicates that a request for change on this line item cannot be processed as the referenced item cannot be located in his application system an ACTION REQUEST CODE "10" indicates "NOT FOUND". If the line item has not changed in status and no action has been taken, and the item is transmitted for information purposes or positioning an ACTION REQUEST CODE "11" indicates "NOT AMENDED".
- 01060Additional product idConditionalMax 25
A segment providing either additional identification to the product specified in the LIN segment (e.g. Harmonized System number), or provides any substitute product identification.
- 01070Item descriptionConditionalMax 99
A segment for describing the product or service being ordered as well as product characteristic. This segment should be used for products or services that cannot be fully identified by a product code or article number.
- 01080MeasurementsConditionalMax 99
A segment enabling the physical measurements of the ordered item to be specified where this is required for full identification of the product. Any measurements must refer to the product in its unpacked form. e.g. thickness of plastic film, length, weight, etc.
- 01090QuantityConditionalMax 99
A segment identifying the product quantities e.g. ordered quantity.
- 01100Percentage detailsConditionalMax 5
A segment specifying the strength or yield of a product as a percentage, e.g. 80% to indicate the strength of an Acid.
- 01110Additional informationConditionalMax 5
To indicate that special conditions due to the origin, customs preference, fiscal or commercial factors are applicable.
- 01120Date/time/periodConditionalMax 35
A segment specifying date/time/period details relating to the line item only.
- 01130Monetary amountConditionalMax 10
A segment specifying any monetary amounts relating to the product, e.g. item amount, insurance value, customs value.
- 01140Processing informationConditionalMax 99
A segment used to specify general processing information about the line item.
- 01150Goods identity numberConditionalMax 1000
A segment providing identity numbers to be applied to the goods being ordered, e.g. serial numbers for assembled equipment.
- 01160Related identification numbersConditionalMax 1000
A segment providing sets of related identification numbers for a line item, e.g. engine numbers, chassis number and transmission number for a vehicle.
- 01170Quantity variancesConditionalMax 1
A segment identifying order quantity variances, normally specified by the supplier using an Order Response message.
- 01180Document/message detailsConditionalMax 99
A segment to indicate that a certificate/declaration of origin is required for the ordered article.
- 01190Payment instructionsConditionalMax 1
A segment to indicate that where a central buyer is purchasing on behalf of different consignees, the means of payment may differ for each item/consignee combination as specified in segment group 25.
- 01200Maintenance operation detailsConditionalMax 99
A segment giving details of the maintenance on object relating to the item, such as tools and packages. The party that is responsible as well as who is paying, can also be given.
- 01210Free textConditionalMax 99
A segment with free text information, in coded or clear form, used when additional information is needed but cannot be accommodated within other segments. In computer to computer exchanges such text will normally require the receiver to process this segment manually.
- Segment group 28Repeat 999
- 01230Characteristic/class idMandatoryMax 1
A segment to identify product characteristic and, or the characteristic name and characteristic relevance for the business process.
- 01240Characteristic valueConditionalMax 10
A segment to specify common product characteristic by value in either coded form or in free format.
- 01250MeasurementsConditionalMax 10
A segment indicating characteristic value being physical measurement (including measurable quantities and percentages) related to specified product characteristics (for example voltage, percentage of material contained) and where relevant measurement ranges.
- 01230Characteristic/class idMandatoryMax 1
- Segment group 29Repeat 10
- 01270Payment termsMandatoryMax 1
A segment identifying the payment terms and date/time basis.
- 01280Date/time/periodConditionalMax 5
A segment giving the specific date/time/period, if needed, of any payments, discounts, instalments etc.
- 01290Percentage detailsConditionalMax 1
A segment specifying the discount, interest, penalty as well as instalment percentage.
- 01300Monetary amountConditionalMax 1
A segment specifying amounts related to payment discounts, penalties or instalments.
- 01270Payment termsMandatoryMax 1
- Segment group 30Repeat 1
- 01320Adjustment detailsMandatoryMax 1
A segment giving adjustment details.
- 01330Free textConditionalMax 5
A segment giving additional information on the adjustment.
- 01320Adjustment detailsMandatoryMax 1
- Segment group 31Repeat 25
- 01350Price detailsMandatoryMax 1
A segment to specify the price type and amount. The price used in the calculation of the line amount will be identified as 'Unit Price'.
- 01360CurrenciesConditionalMax 1
A segment to allow to specify the price in a different currency that in segment group 7.
- 01370Additional price informationConditionalMax 1
A segment to identify pricing information such as a price multiplier, the class or type of trade and additionally identifying the reason for any changes.
- 01380Range detailsConditionalMax 1
A segment to identify the ranges(quantity, amount, etc) to which the additional price information applies.
- 01390Date/time/periodConditionalMax 5
A segment to identify the date/time/period information related to the price change. e.g. period of validity.
- 01350Price detailsMandatoryMax 1
- Segment group 32Repeat 9999
- 01410ReferenceMandatoryMax 1
A segment identifying the reference by its number and where appropriate a line number within a document.
- 01420Date/time/periodConditionalMax 5
A segment specifying the date/time related to the reference.
- 01410ReferenceMandatoryMax 1
- Segment group 33Repeat 99
- 01440PackageMandatoryMax 1
A segment specifying the number of packages and the physical type of packaging for the line item, e.g. pallet type.
- 01450MeasurementsConditionalMax 5
A segment specifying physical measurements of packages described in the PAC segment. e.g. cube or gross weight.
- 01460QuantityConditionalMax 5
A segment specifying the maximum quantity number of packages which can be stacked safely on each other and/or the number of items normally contained within the package.
- 01470Date/time/periodConditionalMax 5
A segment to indicate the validity period in relation to the specified article.
- Segment group 34Repeat 1
- 01490ReferenceMandatoryMax 1
A segment identifying the packing instruction document.
- 01500Date/time/periodConditionalMax 5
A segment specifying the date/time related to the referenced document.
- 01490ReferenceMandatoryMax 1
- Segment group 35Repeat 99
- 01520Package identificationMandatoryMax 1
A segment specifying markings and labels used on individual physical units (packages) described in the PAC segment.
- 01530ReferenceConditionalMax 1
A segment identifying the master label number.
- 01540Date/time/periodConditionalMax 5
A segment specifying the dates relevant to the package markings.
- 01550Goods identity numberConditionalMax 99
A segment identifying the number or ranges of numbers for use with the package markings.
- 01520Package identificationMandatoryMax 1
- 01440PackageMandatoryMax 1
- Segment group 36Repeat 9999
- 01570Place/location identificationMandatoryMax 1
A segment indicating the location to which part of the consignment is to be delivered.
- 01580Percentage detailsConditionalMax 1
A segment specifying the percentage of the quantity to be delivered to the identified location.
- 01590Date/time/periodConditionalMax 5
A segment specifying the dates and/or times that the delivery should be made.
- Segment group 37Repeat 99
- 01610QuantityMandatoryMax 1
A segment specifying the quantity to be delivered to the identified location.
- 01620StatusConditionalMax 99
A segment specifying the status of the quantity, including its category and the reason(s) for the status.
- 01610QuantityMandatoryMax 1
- 01570Place/location identificationMandatoryMax 1
- Segment group 38Repeat 10
- 01640Duty/tax/fee detailsMandatoryMax 1
A segment specifying a tax type, category and rate, or exemption, relating to the line item.
- 01650Monetary amountConditionalMax 1
A segment specifying the amount for the identified tax/fee.
- 01660Place/location identificationConditionalMax 5
A segment indicating the location to which the tax or exemption specified in the TAX segment applies, e.g. city or state tax.
- 01640Duty/tax/fee detailsMandatoryMax 1
- Segment group 39Repeat 999
- 01680Name and addressMandatoryMax 1
A segment identifying names and addresses of the parties, in coded or clear form, and their functions relevant to the order. It is recommended that where possible only the coded form of the party ID should be specified. e.g. The Buyer and Seller are known to each other, thus only the coded ID is required, but the Consignee or Delivery address may vary and would have to be clearly specified, preferably in structured format.
- 01690Place/location identificationConditionalMax 5
A segment giving more specific location information of the party specified in the NAD segment e.g. internal site/building number.
- 01700Financial institution informationConditionalMax 5
A segment identifying the financial institution (e.g. bank) and relevant account numbers for the seller, buyer and where necessary other parties e.g. the buyer may provide a choice of financial institutions for direct debit purposes.
- Segment group 40Repeat 99
- 01720ReferenceMandatoryMax 1
A segment identifying the reference by its number and where appropriate a line number within a document.
- 01730Date/time/periodConditionalMax 5
A segment specifying the date and/or time related to the reference.
- 01720ReferenceMandatoryMax 1
- Segment group 41Repeat 5
- 01750Document/message detailsMandatoryMax 1
A segment identifying and providing information relating to the documents required by the party specified by the NAD segment. For example, the party may require a Certificate of Analysis.
- 01760Date/time/periodConditionalMax 5
A segment specifying the date and/or time of the document.
- 01750Document/message detailsMandatoryMax 1
- Segment group 42Repeat 5
- 01780Contact informationMandatoryMax 1
A segment to identify a person or department, and their function, to whom communications should be directed.
- 01790Communication contactConditionalMax 5
A segment to identify a communications type and number for the contact specified in the CTA segment.
- 01780Contact informationMandatoryMax 1
- Segment group 43Repeat 99
- 01810QuantityMandatoryMax 1
A segment specifying the quantity to be delivered to the related party.
- 01820Date/time/periodConditionalMax 5
A segment specifying the dates and/or times that the delivery should be made.
- 01830StatusConditionalMax 99
A segment specifying the status of the quantity, including its category and the reason(s) for the status.
- 01810QuantityMandatoryMax 1
- 01680Name and addressMandatoryMax 1
- Segment group 44Repeat 99
- 01850Allowance or chargeMandatoryMax 1
A segment identifying the charge or allowance and, where necessary its calculation sequence.
- 01860Additional informationConditionalMax 5
A segment indicating that the allowance or charge specified is subject to special conditions owing to origin, customs preference or commercial factors.
- 01870Date/time/periodConditionalMax 5
A segment to identify the date/time/period information related to the allowance or charge, e.g. period of validity.
- Segment group 45Repeat 1
- 01890QuantityMandatoryMax 1
A segment identifying the type of quantity and the quantity related to the allowance or charge.
- 01900Range detailsConditionalMax 1
A segment specifying, if required, the range to which the allowance or charge applies.
- 01890QuantityMandatoryMax 1
- Segment group 46Repeat 1
- 01920Percentage detailsMandatoryMax 1
A segment identifying the percentage and the percentage basis for the calculation of the allowance or charge.
- 01930Range detailsConditionalMax 1
A segment specifying, if required, a range for the application of the percentage.
- 01920Percentage detailsMandatoryMax 1
- Segment group 47Repeat 2
- 01950Monetary amountMandatoryMax 1
A segment identifying the monetary amount for the allowance or charge.
- 01960Range detailsConditionalMax 1
A segment specifying, if required, a range for the application of the allowance/charge amount.
- 01950Monetary amountMandatoryMax 1
- Segment group 48Repeat 1
- 01980Rate detailsMandatoryMax 1
A segment specifying the rate per unit and the basis for calculation.
- 01990Range detailsConditionalMax 1
A segment specifying, if required, the range for the application of the allowance/charge rate.
- 01980Rate detailsMandatoryMax 1
- Segment group 49Repeat 5
- 02010Duty/tax/fee detailsMandatoryMax 1
A segment specifying the tax type, category and rate, or exemption, related to the allowance or charge.
- 02020Monetary amountConditionalMax 1
A segment specifying the tax amount for the allowance or charge.
- 02010Duty/tax/fee detailsMandatoryMax 1
- 01850Allowance or chargeMandatoryMax 1
- Segment group 50Repeat 10
- 02040Transport informationMandatoryMax 1
A segment specifying the mode, means and identification of the transport for the goods item being ordered, where this is different to or not specified within the heading section.
040 D5(040,030) If first, then all - Segment group 51Repeat 10
- 02060Place/location identificationMandatoryMax 1
A segment identifying locations relevant to the transport specified in the TDT segment.
- 02070Date/time/periodConditionalMax 5
A segment identifying the date/time details of departure and/or arrival of the transported goods for the specified location.
- 02060Place/location identificationMandatoryMax 1
- 02040Transport informationMandatoryMax 1
- Segment group 52Repeat 5
- 02090Terms of delivery or transportMandatoryMax 1
A segment identifying the delivery terms to be used.
- 02100Place/location identificationConditionalMax 2
A segment identifying locations relevant to the delivery terms specified in the TOD segment.
- 02090Terms of delivery or transportMandatoryMax 1
- Segment group 53Repeat 10
- 02120Equipment detailsMandatoryMax 1
A segment to define fixed information regarding equipment to be used in conjunction with the ordered item, and if required, to indicate responsibility for supply of the equipment, e.g. a container identification.
- 02130Handling instructionsConditionalMax 5
A segment providing information on required handling of materials and additionally, if required, identifying hazardous materials in the ordered item.
- 02140MeasurementsConditionalMax 5
A segment providing measurement information for the equipment.
- 02150Free textConditionalMax 5
A segment with free text information, in coded or clear form, to give further clarification, when required, to the equipment and handling details. In computer to computer exchanges such text will normally require the receiver to process this segment manually.
- 02120Equipment detailsMandatoryMax 1
- Segment group 54Repeat 100
- 02170Scheduling conditionsMandatoryMax 1
A segment specifying the type and status of the schedule being given, and optionally defining a pattern to be established, e.g. firm or proposed delivery schedule for a weekly pattern.
- 02180Free textConditionalMax 5
A segment with free text information, in coded or clear form, used when additional information is needed but cannot be accommodated within other segments. In computer to computer exchanges such text will normally require the receiver to process this segment manually.
- 02190ReferenceConditionalMax 5
A segment for specifying references relevant to a schedule.
- Segment group 55Repeat 10
- 02210QuantityMandatoryMax 1
A segment to specify pertinent quantities relating to the schedule and pattern established in the SCC segment, e.g. delivery quantity.
- 02220Date/time/periodConditionalMax 5
A segment indicating the date/time details relating to the quantity and schedule details in the SCC/QTY segments. This segment may be repeated to indicate date/time ranges, e.g. start and end dates for a delivery pattern, or delivery window.
- 02210QuantityMandatoryMax 1
- 02170Scheduling conditionsMandatoryMax 1
- Segment group 56Repeat 999
- 02240Requirements and conditionsMandatoryMax 1
A segment to enable industry or national requirements to be specified.
- 02250ReferenceConditionalMax 5
A segment identifying the referenced document by its number and, where appropriate, a line number.
- 02260Date/time/periodConditionalMax 5
A segment indicating the date/time details relating to the references.
- 02270Free textConditionalMax 99999
A segment with free text information, in coded or clear form, used when additional information is needed but cannot be accommodated within other segments. In computer to computer exchanges such text will normally require the receiver to process this segment manually.
- 02240Requirements and conditionsMandatoryMax 1
- Segment group 57Repeat 10
- 02290StagesMandatoryMax 1
A segment providing information related to the kind of stage in a process, the total number of stages and the current stage.
- Segment group 58Repeat 3
- 02310QuantityMandatoryMax 1
A segment giving information on quantity relating to STG.
- 02320Monetary amountConditionalMax 1
A segment giving information on monetary amount relating to STG.
- 02310QuantityMandatoryMax 1
- 02290StagesMandatoryMax 1
- Segment group 59Repeat 99
- 02340External file link identificationMandatoryMax 1
This segment will identify the external files by indicating the file name, file number and its sequence number in an exchange.
- 02350Computer environment detailsConditionalMax 99
To give precise definitions of all necessary elements belonging to the configuration of a computer system, e.g. hardware, firmware, operating system, communication and application software.
- 02360Communication contactConditionalMax 9
To identify a communication number of a department or a person to whom communication should be directed.
- 02370ReferenceConditionalMax 9
A segment giving reference related to the file identified by a previous external file link identification segment.
- 02380Date/time/periodConditionalMax 9
This segment will convey the date/time details of the external file.
- 02390QuantityConditionalMax 9
The size/volume of the external file identified in the previous external file link identification segment.
- 02340External file link identificationMandatoryMax 1
- 01050Line itemMandatoryMax 1
Summary
- 02400Section controlMandatoryMax 1
A service segment placed at the start of the summary section to avoid segment collision.
- 02410Monetary amountConditionalMax 12
A segment giving the total amounts for the whole order response message.
- 02420Control totalConditionalMax 10
A segment by which control totals may be provided by the sender for checking by the receiver.
- Segment group 60Repeat 10
- 02440Allowance or chargeMandatoryMax 1
A segment identifying the charge or allowance type to be summarised.
- 02450Additional informationConditionalMax 1
A segment indicating that allowance or charge specified is subject to special conditions owing to origin, customs preference or commercial factors.
- 02460Monetary amountMandatoryMax 2
A segment specifying the summary amount for the allowance or charge.
- 02440Allowance or chargeMandatoryMax 1
- 02470Message trailerMandatoryMax 1
A service segment ending a message, giving the total number of segments in the message (including the UNH & UNT) and the control reference number of the message.
1. 0062, the value shall be identical to the value in 0062 in thecorresponding UNH segment.