X12 214 Air Shipment Status Message (Consignee/Shipper)
This Draft Standard for Trial Use contains the format and establishes the data contents of the Transportation Carrier Shipment Status Message Transaction Set (214) for use within the context of an Electronic Data Interchange (EDI) environment. This transaction set can be used by a transportation carrier to provide shippers, consignees, and their agents with the status of shipments in terms of dates, times, locations, route, identifying numbers, and conveyance.
- ~ Segment
- * Element
- > Component
Interchange Control Header
To start and identify an interchange of zero or more functional groups and interchange-related control segments
Code to identify the type of information in the Authorization Information
- 00
- No Authorization Information Present (No Meaningful Information in I02)
Information used for additional identification or authorization of the interchange sender or the data in the interchange; the type of information is set by the Authorization Information Qualifier (I01)
Code to identify the type of information in the Security Information
- 00
- No Security Information Present (No Meaningful Information in I04)
This is used for identifying the security information about the interchange sender or the data in the interchange; the type of information is set by the Security Information Qualifier (I03)
Qualifier to designate the system/method of code structure used to designate the sender or receiver ID element being qualified
Identification code published by the sender for other parties to use as the receiver ID to route data to them; the sender always codes this value in the sender ID element
Qualifier to designate the system/method of code structure used to designate the sender or receiver ID element being qualified
Identification code published by the receiver of the data; When sending, it is used by the sender as their sending ID, thus other parties sending to them will use this as a receiving ID to route data to them
Code to identify the agency responsible for the control standard used by the message that is enclosed by the interchange header and trailer
- U
- U.S. EDI Community of ASC X12, TDCC, and UCS
This version number covers the interchange control segments
- 00401
- Draft Standards for Trial Use Approved for Publication by ASC X12 Procedures Review Board through October 1997
A control number assigned by the interchange sender
Code sent by the sender to request an interchange acknowledgment (TA1)
- 0
- No Acknowledgment Requested
- 1
- Interchange Acknowledgment Requested
Code to indicate whether data enclosed by this interchange envelope is test, production or information
- I
- Information
- P
- Production Data
- T
- Test Data
Type is not applicable; the component element separator is a delimiter and not a data element; this field provides the delimiter used to separate component data elements within a composite data structure; this value must be different than the data element separator and the segment terminator
- >
- Component Element Separator
Functional Group Header
To indicate the beginning of a functional group and to provide control information
Code identifying a group of application related transaction sets
- QM
- Transportation Carrier Shipment Status Message (214)
Code identifying party sending transmission; codes agreed to by trading partners
Code identifying party receiving transmission. Codes agreed to by trading partners
Time expressed in 24-hour clock time as follows: HHMM, or HHMMSS, or HHMMSSD, or HHMMSSDD, where H = hours (00-23), M = minutes (00-59), S = integer seconds (00-59) and DD = decimal seconds; decimal seconds are expressed as follows: D = tenths (0-9) and DD = hundredths (00-99)
Assigned number originated and maintained by the sender
Code used in conjunction with Data Element 480 to identify the issuer of the standard
- T
- Transportation Data Coordinating Committee (TDCC)
- X
- Accredited Standards Committee X12
Code indicating the version, release, subrelease, and industry identifier of the EDI standard being used, including the GS and GE segments; if code in DE455 in GS segment is X, then in DE 480 positions 1-3 are the version number; positions 4-6 are the release and subrelease, level of the version; and positions 7-12 are the industry or trade association identifiers (optionally assigned by user); if code in DE455 in GS segment is T, then other formats are allowed
- 004010
- Draft Standards Approved for Publication by ASC X12 Procedures Review Board through October 1997
Heading
Transaction Set Header
To indicate the start of a transaction set and to assign a control number
Code uniquely identifying a Transaction Set
- The transaction set identifier (ST01) used by the translation routines of the interchange partners to select the appropriate transaction set definition (e.g., 810 selects the Invoice Transaction Set).
- 214
- Transportation Carrier Shipment Status Message
Beginning Segment for Transportation Carrier Shipment Status Message
To transmit identifying numbers and other basic data relating to the transaction set
Reference information as defined for a particular Transaction Set or as specified by the Reference Identification Qualifier
- B1001 is the carrier assigned reference number.
- B1001 is the carrier's PRO (invoice number) that identifies the shipment.
FLEX_ID – This is the shipper’s shipment identifier
Identification number assigned to the shipment by the shipper that uniquely identifies the shipment from origin to ultimate destination and is not subject to modification; (Does not contain blanks or special characters).
Shipper's Shipment Identifying Number
Business Instructions and Reference Number
To specify instructions in this business relationship or a reference number
Reference information as defined for a particular Transaction Set or as specified by the Reference Identification Qualifier.
The requirement for references is dependent upon specific customer needs.
Code qualifying the Reference Identification
- 19
- Division Identifier
- AF
- Airlines Flight Identification Number
- SCA
- Standard Carrier Alpha Code (SCAC)
Name
To identify a party by type of organization, name, and code
Code identifying an organizational entity, a physical location, property or an individual
- CN
- Consignee
- DT
- Destination Terminal
- OT
- Origin Terminal
- SH
- Shipper
Code designating the system/method of code structure used for Identification Code (67)
- 94
- Code assigned by the organization that is the ultimate destination of the transaction set
Code identifying a party or other code
- This segment, used alone, provides the most efficient method of providing organizational identification. To obtain this efficiency the "ID Code" (N104) must provide a key to the table maintained by the transaction processing party.
Based on the 01 qualifier, the 04 value is:
CN = ID key recognizable to receiving partner
DT = port location code
OT = port location code
SH = ID key recognizable to receiving partner
Code describing entity relationship
- N105 and N106 further define the type of entity in N101.
Address Information
To specify the location of the named party
Address information.
IF N101=’CN’ > Consignee Address Line 1
IF N101=’SH’ > Shipper Address Line 1
Geographic Location
To specify the geographic place of the named party
Free-form text for city name
- A combination of either N401 through N404, or N405 and N406 may be adequate to specify a location.
IF N101=’CN’ > Consignee City Name
IF N101=’DT’ > Port of Discharge City Name
IF N101=’OT’ > Port of Loading City Name
IF N101=’SH’ > Shipper City Name
See Note 1 Below
Code (Standard State/Province) as defined by appropriate government agency
- N402 is required only if city name (N401) is in the U.S. or Canada.
IF N101=’CN’ > Consignee State
IF N101=’DT’ > Port of Discharge State
IF N101=’OT’ > Port of Loading State
IF N101=’SH’ > Shipper State
See Note 1, 2 Below
Code defining international postal zone code excluding punctuation and blanks (zip code for United States).
IF N101=’CN’ > Consignee Zip Code
IF N101=’DT’ > not required
IF N101=’OT’ > not required
IF N101=’SH’ > Shipper Zip Code
Code identifying the country.
IF N101=’CN’ > Consignee Country Code
IF N101=’DT’ > Port of Discharge Country Code
IF N101=’OT’ > Port of Loading Country Code
IF N101=’SH’ > Shipper Country Code
Code identifying type of location
- IA
- International Air Transport Association (IATA) Location Qualifier
- UN
- United Nations Location Code (UNLOCODE)
Date/Time
To specify pertinent dates and times
- Status and appointment dates and times shall not be transmitted in the G62 segment.
Code specifying type of date
- 17
- Estimated Delivery Date
- 69
- Scheduled Pick-Up Date
Date expressed as CCYYMMDD.
IF N101=’SH’ and G6201=’69’ set from Scheduled Pickup Date
IF N101=’CN’ and G6201=’17’ set from Estimated Delivery Date
Time expressed in 24-hour clock time as follows: HHMM, or HHMMSS, or HHMMSSD, or HHMMSSDD, where H = hours (00-23), M = minutes (00-59), S = integer seconds (00-59) and DD = decimal seconds; decimal seconds are expressed as follows: D = tenths (0-9) and DD = hundredths (00-99)
Code identifying the time. In accordance with International Standards Organization standard 8601, time can be specified by a + or - and an indication in hours in relation to Universal Time Coordinate (UTC) time; since + is a restricted character, + and - are substituted by P and M in the codes that follow
Interline Information
To identify the interline carrier and relevant data
Standard Carrier Alpha Code
- MS301 is the Standard Carrier Alpha Code (SCAC) of the interline carrier.
Code describing the relationship of a carrier to a specific shipment movement
- O
- Origin Carrier (Air, Motor, or Ocean)
Free-form text for city name
- MS303 is the city where the interline was performed.
Code specifying the method or type of transportation for the shipment
- A
- Air
Assigned Number
To reference a line number in a transaction set
Shipment Status Details
To specify the status of a shipment, the reason for that status, the date and time of the status and the date and time of any appointments scheduled.
Code indicating the status of a shipment
- If AT701 is present, AT705 is the date the status occurred. If AT703 is present, AT705 is a date related to an appointment.
- If AT701 is present, AT706 is the time of the status. If AT703 is present, AT706 is the time of the appointment.
- B6
- Estimated to Arrive at Carrier Terminal
- D1
- Completed Unloading at Delivery Location
- P1
- Departed Terminal Location
- X2
- Estimated Date and/or Time of Arrival at Consignee's Location
- X4
- Arrived at Terminal Location
Code indicating the reason a shipment status or appointment reason was transmitted
- NS
- Normal Status
Code indicating the status of an appointment to pick-up or deliver a shipment
Code indicating the reason a shipment status or appointment reason was transmitted
Time expressed in 24-hour clock time as follows: HHMM, or HHMMSS, or HHMMSSD, or HHMMSSDD, where H = hours (00-23), M = minutes (00-59), S = integer seconds (00-59) and DD = decimal seconds; decimal seconds are expressed as follows: D = tenths (0-9) and DD = hundredths (00-99)
Status event time
Code identifying the time. In accordance with International Standards Organization standard 8601, time can be specified by a + or - and an indication in hours in relation to Universal Time Coordinate (UTC) time; since + is a restricted character, + and - are substituted by P and M in the codes that follow
- If AT707 is not present then AT706 represents local time of the status.
- LT
- Local Time
- UT
- Universal Time Coordinate
Equipment, Shipment, or Real Property Location
To specify the location of a piece of equipment, a shipment, or real property in terms of city and state or longitude and latitude
Code (Standard State/Province) as defined by appropriate government agency
- 0I
- IATA Code
- ZZ
- Mutually defined, city name or code
Code indicating the longitude in degrees (3 positions), minutes (2 positions), and seconds (2 positions)
- MS104 is the longitude expressed in Degrees, Minutes, and Seconds.
Code indicating the latitude in degrees (3 positions), minutes (2 positions), seconds (2 positions)
- MS105 is the latitude expressed in Degrees, Minutes, and Seconds.
Code identifying geographic direction
- MS106 may only be 'E' or 'W'.
Remarks
To transmit information in a free-form format for comment or special instruction
Shipment Weight, Packaging and Quantity Data
To specify shipment details in terms of weight, and quantity of handling units
Number of units (pieces) of the lading commodity
- AT804 is the quantity of handling units that are not unitized (for example a carton). When added to the quantity in AT805, it is the total quantity of handling units in the shipment.
Number of units (pieces) of the lading commodity
- AT805 is the quantity of handling units that are unitized (for example on a pallet or slip sheet). When added to the quantity in AT804 it is the total quantity of handling units for the shipment.
Code identifying the volume unit
- E
- Cubic Feet
- X
- Cubic Meters
Transaction Set Trailer
To indicate the end of the transaction set and provide the count of the transmitted segments (including the beginning (ST) and ending (SE) segments)
Total number of segments included in a transaction set including ST and SE segments
Functional Group Trailer
To indicate the end of a functional group and to provide control information
Total number of transaction sets included in the functional group or interchange (transmission) group terminated by the trailer containing this data element
Interchange Control Trailer
To define the end of an interchange of zero or more functional groups and interchange-related control segments
Sample 214 (1)
B10*FLEX004*FLEX004*FLEX~
L11*KL0420*AF~
L11*Unidentified Airlines*SCA~
N1*SH*CUSTOMER CHINA*94*123456~
N3*Shanghai Shi, Minhang Qu*3rd Floor, Shopping Plaza, No.1, Lane 12,~
N4*Shanghai*31**CN*UN*CNSHA~
G62*69*20180831~
N1*OT*SHANGHAI PUDONG INTERNATIONAL AIRPORT*94*PVG~
N4*Shanghai***CN*IA*PVG~
N1*DT*AMSTERDAM AIRPORT SCHIPHOL, HAARLEMMERMEER, NETHERLANDS*94*AMS~
N4*Amsterdam***NL*IA*AMS~
N1*CN*CUSTOMER BV*94*666666~
N3*Wilhelminakade 909~
N4*Rotterdam*AP*3072*NL*UN*NLRTM~
G62*17*20180910~
MS3*KL*O**A~
LX*1~
AT7*D1*NS***20180910*0600*LT~
MS1*AMS*0I*NL~
K1*comments~
AT8*G*K*1000*15**X*30~
SE*23*0001~
Sample 214 (2)
B10*FLEX004*FLEX004*FLEX~
L11*KL0420*AF~
L11*Unidentified Airlines*SCA~
N1*SH*CUSTOMER CHINA*94*123456~
N3*Shanghai Shi, Minhang Qu*3rd Floor, Shopping Plaza, No.1, Lane 13,~
N4*Shanghai*31**CN*UN*CNSHA~
G62*69*20180831~
N1*OT*SHANGHAI PUDONG INTERNATIONAL AIRPORT*94*PVG~
N4*Shanghai***CN*IA*PVG~
N1*DT*AMSTERDAM AIRPORT SCHIPHOL, HAARLEMMERMEER, NETHERLANDS*94*AMS~
N4*Amsterdam***NL*IA*AMS~
N1*CN*CUSTOMER BV*94*666666~
N3*Wilhelminakade 909~
N4*Rotterdam*AP*3072*NL*UN*NLRTM~
G62*17*20180910~
MS3*KL*O**A~
LX*1~
AT7*B6*NS***20180906*0600*LT~
MS1*AMS*0I*NL~
K1*comments~
AT8*G*K*1000*15**X*30~
SE*23*0001~
Stedi is a registered trademark of Stedi, Inc. All names, logos, and brands of third parties listed on this page are trademarks of their respective owners (including “X12”, which is a trademark of X12 Incorporated). Stedi, Inc. and its products and services are not endorsed by, sponsored by, or affiliated with these third parties. Use of these names, logos, and brands is for identification purposes only, and does not imply any such endorsement, sponsorship, or affiliation.